The lovely Kathy Priday of Wicked Lady Chains has been kind enough to make a video out of my Life Pendant tutorial! I wanted you all to have a chance to see it, so here you go. 😀
Life Pendant Tutorial
By Victoria Sol
This is a fairly simple pendant to make. The only real challenge is that you need to make two mobius units – in different directions! If you haven’t done this before, never fear. I will explain as best I can and if you’re finding it tricky, you can contact me in a comment on my blog and I’ll try my best to help further.
Now. You’re going to need the following ring sizes, or close enough (the pendant is relatively forgiving like that):
2.4mm WD, 27.5mm ID (AR 11.5) – 1 ring
1.6mm WD, 11.2mm ID (AR 7.1) – 10 rings
1.2mm WD, 8.5mm ID (AR 7.2) – 4 rings
1mm WD, 4mm ID (AR 4) – 20 rings
You can buy kits in my Etsy shop which contain enough rings for two pendants. The Bright Aluminium rings in the kits are supplied by Zili, whom I can highly recommend if you want to buy the rings in bulk instead.
Now for the actual instructions:
1. Create two mobius units, facing in different directions. Use the 1.6mm WD rings for this, with 5 rings in each mobius unit. If you’ve never made a mobius unit before, it’s a construct where every ring passes through every other ring. You make it by first closing one ring, then passing another ring through it, making sure to go from the bottom upwards and then lean it to the right. Let the two rings now work as one ring as you pass the next one upwards through both, and lean that one to the right as well. Continue following this pattern until you have a five ring mobius unit. It should look really neat, like in the picture. After you’ve made the first one, make the second one in the same way except lean every ring to the left instead.
If you’re having trouble making mobius units, have a look at the M.A.I.L. website for further instructions: http://www.mailleartisans.org/articles/articledisplay.php?key=244
2. Close the big (2.4mm WD) ring. This will be the outer frame.
3. Connect one mobius unit to the frame, one ring at a time, using the smallest (1mm WD) rings. Make sure the mobius keeps its form during this – that the rings stay in the same orientation. It’s really easy to lose track of the rings during this step, so I’d recommend laying the whole thing down onto a table now and then to check the mobius unit is still neat.
4. Connect the other mobius to the frame. Bet you didn’t see that coming! The first one will probably slide around a little bit, but try to get the two sections on roughly opposite sides of the frame.
It should now look like this:
5. Here comes the frustrating bit. You will now use two 1.2mm wire rings to connect the two mobius units (connected to the frame) together. Make sure you pass the rings through the very centre of the mobius units so every ring is connected to the other mobius section. Don’t lose hope if you can’t do it in five seconds, it sometimes takes me several minutes and it’s my design! Just be patient and keep at it. The second ring should be easier than the first, as you’ve already created a path.
6. Finally, connect the last remaining of the same rings to the top of the frame ring to create a bail. You can now connect a chain, leather cord or any other kind of fastening you’d like.
I hope you found this tutorial easy to follow and the pendant fun to make! Let me know what you think and I would love to see pictures of your finished pieces. Post them on my Facebook Page, tweet me or tag me on Instagram. I promise I’ll reply. 🙂
Victoria Sol appreciates etiquette:
As sold by Victoria Sol, the recommended retail price for this pendant is £15. Remember to value your skills and charge accordingly.
Please consider giving credit to the designer when selling or showcasing this design.
Thank you for reading!
This tutorial is copyright © Victoria Stedje 2016. Please do not reproduce, copy or teach this tutorial without express consent.
Items made using this tutorial can be sold freely.